|
|
| 产品展示 |
|
Klüberpaste 46 MR 401详细说明 （浏览1416次）
Klüberpaste 46 MR 401
White multi-purpose lubricating paste
The data in this product information is based on our general experience and knowledge at the time of printing and is intended to give information of possible applications to a reader
with technical experience. It constitutes neither an assurance of product properties nor does it release the user from the obligation of performing preliminary tests with the selected
product. We recommend contacting our Technical Consulting Staff to discuss your specific application. If required and possible we will be pleased to provide a sample for testing.
Klüber products are continually improved. Therefore, Klüber Lubrication reserves the right to change all the technical data in this product information at any time without notice.
Klüber Lubrication, a member of the Freudenberg group
Publisher and Copyright: Reprints, total or in part, are permitted if source Klüber Lubrication München KG
Klüber Lubrication München KG is indicated and voucher copy is forwarded. Geisenhausenerstraße 7, 81379 München, Deutschland
+49 89 7876-0, Telefax +49 89 7876-333, klueber.com
Product information 5.150 en Edition 11.08, replaces edition 02.08
Article number: 005108 MA-TM/TP
Description
Klüberpaste 46 MR 401 is a whitish
lubricating paste with a synthetic base
oil, lithium soap and special solid
lubricant additives.
This paste is suitable for long-term and
lifetime lubrication, as an assembly
lubricant and for lubrication points
subject to fretting corrosion.
It has a wide service temperature range*
from approx. –40 to 150 °C, shows
neutral behaviour towards non-ferrous
metals, many plastic materials and
rubber, and has a good load carrying
capacity.
Application
Klüberpaste 46 MR 401 is especially
suitable as an assembly lubricant in
press-on processes and as a thin-film
lubricant for all friction points subject to
very high pressure, low sliding speed,
high wear, stick-slip, oscillating
movements, vibrations and tribocorrosion.
The paste’s application range includes:
pressing in of pins and bolts, mounting of
rolling bearings, wheels and flanges,
lubrication of rolling and plain bearings
operating at very low speeds, for
threaded spindles, spline shafts and
adjusting nuts to prevent running-in
damage and stick-slip; for ball-andsocket
joints, pin suspensions, screw
connections, rotary shaft seals (O-ring
seals, V-ring gaskets, collars) made of
rubber materials to extend the service
life.
S = standard deviation
1 = for batches with batch no. > 628909
Application notes
Before applying Klüberpaste
46 MR 401 it is important to clean the
contact surfaces and remove any solvent
residues with a lint-free, dry cloth.
Klüberpaste 46 MR 401 can be easily
applied to the entire surface in a thin
layer with a spatula. It is important to
avoid overlubrication.
Before applying the paste to a plastic
material we recommend carrying out a
compatibility test.
Minimum shelf life
The minimum shelf life is approx. 36
months if the product is stored in its
unopened original container in a dry
place.
Pack sizes
60 g tube
600 g cartridge
0.75 kg can
30 kg drum
Material safety data sheets can be
downloaded or requested via our
website klueber.com. You may
also obtain them through your
contact person at Klüber.
Klüberpaste 46 MR 401
• Whitish high-performance
lubricating paste
• Facilitates assembly and
disassembly
• Protects from running-in
damage and prevents seizure
• Has a very high load-carrying
capacity
• Improves lubrication in case of
oscillating movements or
vibrations – provides protection
against tribo-corrosion
• Is resistant to water and is not
washed out
• Provides good corrosion
protection
Product data1
Colour whitish
Service temperature range*, °C, approx. -40 – 150
Base oil viscosity, DIN 51 562 pt. 01, at 40 °C, mm2/s 350 – 375
Drop point, DIN ISO 2176, °C > 185
Worked penetration at 25 °C, DIN ISO 2137,
(ASTM D 217); 0.1 mm 300 – 340
Corrosion protection SKF-Emcor test, DIN 51 802,
1 week, distilled water, corrosion rating ≤ 1
Copper corrosion, DIN 51 811,
after 24 h / 100 °C, corrosion rating 1 – 100
Four-ball test, welding force, DIN 51 350 Pt 4, N > 4600
Friction coefficients in first-time tightening, measured in
screw connections M10x30-8.8, DIN EN ISO 4017, black,
and nut M10-8, DIN EN ISO 4032, bright; number of
screws: 20
μhead = 0.17 S=0.011
μthread = 0.15 S=0.024
* Service temperatures are guide values which depend on the lubricant’s composition, the intended use and the application
method. Lubricants change their consistency, apparent dynamic viscosity or viscosity depending on the mechanodynamical
loads, time, pressure and temperature. These changes in product characteristics may affect the function of a |
|
|
